Tridonic 24166312 LCI 015/0350 E020

24166312 Common Data

Rated supply voltage 120 – 240 V
AC voltage range 108 – 264 V
DC voltage range 120 – 240 V
Rated current (at 230 V 50 Hz) 0.08 A
Mains frequency 50 / 60 Hz
Efficiency > 75 %
Max. input power 17 W
λ (at 230 V 50 Hz) 0.91
Output current tolerance2 ± 8 %
Output current ripple ± 32 %
Max. repetitive output peak current 500 mA
Max. non-repetitive output peak current 550 mA
Max. output voltage1 48 V
Starting time (output) ≤ 0.5 s
Turn off time (output) ≤ 1 s
Hold on time at power failure (Output) 10 ms
Ambient temperature ta -25 … +50 °C
Ambient temperature ta (at life-time 50,000 h) -25 … +40 °C
Max. casing temperature tc 70 °C
Storage temperature -30 … +85 °C
Life-time up to 50,000 h
Dimensions LxWxH 165 x 43 x 30 mm
Hole spacing D 142 mm

24166312 Wiring Guidelines

• All connections must be kept as short as possible to ensure good EMI behaviour.
• Mains leads should be kept apart from LED Driver and other leads (ideally 5 – 10 cm distance)
• Max. length of output wires is 2 m.
• Incorrect wiring can damage LED modules.
• To avoid the damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).

24166312 Wiring type and cross section

The wiring can be in stranded wires with ferrules or solid. For perfect function of the screw terminals the strip length should be 7.5–8.5 mm for the terminal.

24166312 Installation instructions

Please note that LCI 015/0350 E020 complies with protection class II so special measures are needed if it is to be installed in protection class I applications / luminaires.

Over temperature protection

Automatic shutdown of the LED Driver if the temperature limit is exceeded. Automatic restart if the temperature falls below the limit.

Overload protection

Automatic shutdown of the LED Driver if the maximum output voltage is exceeded.

Automatic restart if the output voltage is below the limit

Glow wire test according to EN 60695-2-11

850 °C passed

Mounting of device

Max. torque for fixing: 0.5 Nm/M4

Insulation and electric strength testing of luminaires

Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production.

According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each luminaire should be submitted to an insulation test with 500V DC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal.

The insulation resistance must be at least 2MΩ. As an alternative, IEC 60598-1 Annex Q describes a test of the electrical  strength with 1500V AC (or 1.414 x 1500V DC). To avoid damage to the electronic devices this test must not be conducted.

Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.

Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.

In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.

Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.