Tridonic 28000676 LCA 45W 500–1400mA one4all SC – Easy Assembly Cable Shrouds For Independent Use

28000676 Common Data

Rated supply voltage 220 – 240 V
AC voltage range 198 – 264 V
DC voltage range 176 – 280 V

Mains frequency 0 / 50 / 60 Hz
Overvoltage protection 320 V AC, 48 h
Typ. current (at 230 V, 50 Hz, full load) (1)(2) 132 – 224 mA

Typ. current (220 V, 0 Hz, full load, 15 % dimming level) (2) 29 – 44 mA
Leakage current (at 230 V, 50 Hz, full load) (1)(2) < 0.16 mA
Typ. input current in no-load operation 25.7 mA

In-rush current (peak / duration) 23 A / 200 µs
Max. input power 50 W
Typ. power consumption on stand-by (3) < 0.15 W

Typ. input power in no-load operation 0.36 W
Typ. efficiency (at 230 V, 50 Hz, full load) (2) 91 %
λ (at 230 V, 50 Hz, full load) (1) 0.98

THD (at 230 V, 50 Hz, full load) (1) < 5 %
Starting time (at 230 V, 50 Hz, full load) (4) < 0.6 s
Starting time (DC mode) (4) < 0.3 s

Switchover time (AC/DC) (5) < 0.3 s
Turn off time (at 230 V, 50 Hz, full load) < 0.02 s
Output current tolerance (1)(6) ± 3 %

Max. output current peak (non-repetitive) ≤ output current + 40 %
Output LF current ripple (< 120 Hz) ± 2 %
Output P_ST_LM (at full load) ≤ 1

Output SVM (at full load) ≤ 0.4
Max. output voltage (U-OUT) 60 V
Dimming range 1 – 100 %

Mains surge capability (between L – N) 1 kV
Mains surge capability (between L/N – PE) 2 kV
Surge voltage at output side (against PE) < 0.5 kV

Type of protection IP20
Length 150 mm
Width 43 mm
Height 30 mm
Lifetime up to 100000 h

Other Information for the 28000676

28000676 Standards

EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1
EN 61347-2-13
EN 62384
EN 61547
EN 62386-101 (DALI-2)
EN 62386-102 (DALI-2)
EN 62386-207 (DALI-2, inkl. Teil 251, 252, 253)
According to EN 50172 for use in central battery systems
According to EN 60598-2-22 suitable for emergency lighting installations

28000676 Thermal details and lifetime

The LED driver is designed for a lifetime stated above under reference conditions and with a failure probability of less than 10 %.

The relation of tc to ta temperature depends also on the luminaire design.

If the measured tc temperature is approx. 5 K below tc max., ta temperature should be checked and eventually critical components (e.g. ELCAP) measured. Detailed information on request.

28000676 Wiring type and cross section

For wiring use stranded wire with ferrules or solid wire from 0.2–1.5 mm².
Strip 8.5–9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals.
Use one wire for each terminal connector only.
Use each strain relief channel for one cable only

28000676 Wiring guidelines

• Run the secondary lines separately from the mains connections and lines to achieve good EMC performance.
• The max. secondary cable (LED module) length is 2 m (4 m circuit).
• For good EMC performance, keep the LED wiring as short as possible.
• To comply with the EMC regulations run the secondary wires (LED module) in parallel.
• Secondary switching is not permitted.
• The LED driver has no inverse-polarity protection on the secondary side.

Wrong polarity can damage LED modules with no inverse-polarity protection.

• Wrong wiring of the LED driver can lead to malfunction or irreparable damage.
• To avoid damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).

28000676 fixing conditions when using as independent Driver with Clip-On

Dry, acidfree, oilfree, fatfree. It is not allowed to exceed the maximum ambient temperature (ta) stated on the device. Minimum distances stated below are recommendations and depend on the actual luminaire. Is not suitable for fixing in corner.

28000676 Hot plug-in

Hot plug-in is not supported due to residual output voltage of > 0 V. When connecting an LED load, restart the device to activate the LED output.

This can be done via mains reset or via interface (DALI, DSI, switchDIM, ready2mains).

28000676 Earth connection

The earth connection is conducted as protection earth (PE). The LED driver can be earthed via earth terminal. If the LED driver will be earthed, protection earth (PE) has to be used. There is no earth connection required for the functionality of the LED driver. Earth connection is recommended to improve following behaviour:

• Electromagnetic interferences (EMI)
• LED glowing at standby
• Transmission of mains transients to the LED output

In general it is recommended to earth the LED driver if the LED module is mounted on earthed luminaire parts respectively heat sinks and thereby representing a high capacity against earth.

28000676 Electrical values

Make sure that the LED driver is operated within the given window under all operating conditions. Special attention needs to be paid at dimming and DC emergency operation as the forward voltage of the connected LED modules varies with the dimming level, due to the implemented amplitude dimming technology.

Coming below the specified minimum output voltage of the LED driver may cause the device to shut-down

28000676 Dimming

Dimming range 1 % to 100 %

Digital control with:
• DSI signal: 8 bit Manchester Code Speed 1 % to 100 % in 1.4 s
• DALI signal: 16 bit Manchester Code Speed 1 % to 100 % in 0.2 s

Programmable parameter:
Minimum dimming level
Maximum dimming level
Default minimum = 1 %
Programmable range 1 % ≤ MIN ≤ 100 %
Default maximum = 100 %
Programmable range 100 % ≥ MAX ≥ 1 %
Dimming curve is adapted to the eye sensitiveness.
Dimming is realized by amplitude dimming.

28000676 Interfaces / communication

Control input (DA/N, DA/L)

Digital DALI signal or switchDIM can be wired on the same terminals (DA/N and DA/L).
The control input is non-polar for digital control signals (DALI, DSI).
The control signal is not SELV. Control cable has to be installed in accordance to the requirements of low voltage installations.
Different functions depending on each module.

Control input ready2mains (L, N)

The digital ready2mains protocol is modulated onto the mains signal which is wired to the mains terminal (L and N).

switchDIM

Integrated switchDIM function allows a direct connection of a pushbutton for dimming and switching.

Brief push (< 0.6 s) switches LED driver ON and OFF. The dimm level is saved at power-down and restored at power-up.

When the pushbutton is held, LED modules are dimmed. After repush the LED modules are dimmed in the opposite direction.

In installations with LED drivers with different dimming levels or opposite dimming directions (e.g. after a system extension), all LED drivers can be synchronized to 50 % dimming level by a 10 s push.

Use of pushbutton with indicator lamp is not permitted.

switchDIM 2

Version 2 has now the possibility to define different fade times used for short button press events. So the fade time to set memory level (if wake-up from  standby) as well as the fade time to switch off can now be configured.

28000676 Functions

28000676 Function: adjustable current

The output current of the LED driver can be adjusted in a certain range.

For adjustment there are three options available.

Option 1: DALI

Adjustment is done by masterCONFIGURATOR (see masterCONFIGURATOR documentation).

Option 2: I-SELECT 2

By inserting a suitable resistor into the I-SELECT 2 interface, the current value can be adjusted. The relationship between output current and resistor value can be found in the chapter “Accessories I-SELECT 2 Plug

Option 3: ready2mains

Adjustment is done by the ready2mains programmer and the corresponding configuration software (see ready2mains documentation). The priority for current adjustment methods is DALI (highest priority),I-SELECT 2, ready2mains (lowest priority).

ready2mains – configuration
The ready2mains interface can be used to configure the main parameters
of LED drivers via the mains wiring, such as LED output current, CLO and
DC level. These parameters can be adjusted either via ready2mains-capable
configuration software or directly via the ready2mains programmer (output
current only).

ready2mains – dimming

ready2mains allows for mains-based group dimming, controlled via the ready2mains protocol and appropriate dimming interfaces.

For details on the operation of ready2mains and its components see the relevant technical information.

Short-circuit behaviour

In case of a short-circuit at the LED output the LED output is switched off.

After restart of the LED driver the output will be activated again. The restart can either be done via mains reset or via interface (DALI, DSI, switchDIM, ready2mains).

No-load operation

The LED driver will not be damaged in no-load operation. The output will be deactivated and is therefore free of voltage. If a LED load is connected the device has to be restarted before the output will be activated again.

Overload protection

If the maximum load is exceeded by a defined internal limit, the LED driver turns off the LED output. After restart of the LED driver the output will be activated again.
The restart can either be done via mains reset or via interface (DALI, DSI,
switchDIM, ready2mains).

Overtemperature protection

The LED driver is protected against temporary thermal overheating. If the temperature limit is exceeded the output current of the LED module(s) is reduced. The temperature protection is activated above tc max.

The activation temperature differs depending on the LED load. On DC operation this function is deactivated to fulfil emergency requirements.

corridorFUNCTION

The corridorFUNCTION can be programmed in two different ways. To program the corridorFUNCTION by means of software a DALI-USB interface is needed in combination with a DALI PS. The software can be the masterCONFIGURATOR.

To activate the corridorFUNCTION without using software a voltage of 230 V has to be applied for five minutes at the switchDIM connection.

The unit will then switch automatically to the corridorFUNCTION.

Note: If the corridorFUNCTION is wrongly activated in a switchDIM system (for example a switch is used instead of pushbutton), there is the option of installing a pushbutton and deactivating the corridorFUNCTION mode by five short pushes of the button within three seconds.

switchDIM and corridorFUNCTION are very simple tools for controlling gears with conventional pushbuttons or motion sensors.

To ensure correct operation a sinusoidal mains voltage with a frequency of 50 Hz or 60 Hz is required at the control input.

Special attention must be paid to achieving clear zero crossings. Serious mains faults may impair the operation of switchDIM and corridorFUNCTION

Constant Current DALI LED drivers are advanced power supplies that regulate a fixed, consistent, and adjustable output current (e.g.350mA-700mA) for LEDs, while supporting intelligent digital dimming. They are ideal for commercial, architectural, and high-efficiency lighting applications using series-wired fixtures. These drivers enable individual or group, flicker-free dimming (down to 0.1%) using DALI-1 or DALI-2 protocols.

Key Features and Benefits

Constant Current Regulation: Ensures consistent light output and protects LEDs from current fluctuations.

DALI Compatibility: Enables bidirectional communication for control and monitoring.

Flexibility: Many models feature dip switches to select specific amperage outputs (e.g., 250mA, 350mA, 500mA, 700mA).

Dimming Performance: Supports smooth, deep dimming (0.1% to 100%).

Advanced Features: Some models support NFC configuration for setting addresses, dimming curves, and maximum levels without powering on the driver.

Safety & Efficiency: Typically Class 2 rated with high power factors (up to 0.98), making them efficient.

Common Applications

Commercial Lighting: Office and retail spaces.

Architectural Lighting: Accent and cove lighting.

Downlights and Spotlights: Ideal for high-power LED arrays.

Common Specifications

Input Voltage: Usually 100-240V or 220-240V AC.

Output Power: Ranges from low wattage up to 1000W, commonly 10W-60W.

IP Rating: Commonly IP20 for indoor use, though higher ratings are available.

Compliance: IEC 62386 (DALI).

Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.

Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.

In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.

Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.