Tridonic 28002482 LC 20W 500mA fixC SC ADV – Huge UK Based Stock
28002482
Tridonic 28002482 LC 20W 500mA fixC SC ADV
Can be either used for built-in or independent with Tridonic 28001168 ACU SC 43x30mm CLIP-ON SR SET
Constant current LED driver
Temperature protection as per EN 61347-2-13 C5e
Output current 500 mA
Max. output power 22 W
£8.20
Ex.VAT Inc.VAT£9.84
Description
Tridonic 28002482 LC 20W 500mA fixC SC ADV
28002482 Description
Fixed output LED driver
Can be either used built-in or independent with clip-on strain relief clamps available separately (28001534)
Constant current LED driver
For luminaires of protection class I and protection class II
Temperature protection as per EN 61347-2-13 C5e
Output current 500 mA
Max. output power 22 W
28002482 Housing properties
Casing: polycarbonate, white
Type of protection IP20
28002482 Functions
Overtemperature protection
Overload protection
Short-circuit protection
No-load protection
Burst protection voltage 1 kV
Surge protection voltage 1 kV (L to N)
Surge protection voltage 2 kV (L/N to earth)
28002482 Common Data
Rated supply voltage 220 – 240 V
AC voltage range 198 – 264 V
Mains frequency 50 / 60 Hz
Overvoltage protection 320 V AC, 1 h
THD (at 230 V, 50 Hz, full load) < 15 %
Output current tolerance 1 ± 7.5 %
Typ. current ripple (at 230 V, 50 Hz, full load) ± 15 %
Output P_ST_LM (at full load) ≤ 1
Output SVM (at full load) ≤ 0.4
Max. output voltage (U-OUT) 60 V
Starting time (at 230 V, 50 Hz, full load) ≤ 0.5 s
Turn off time (at 230 V, 50 Hz, full load) ≤ 0.2 s
Hold on time at power failure (output) 0 s
Ambient temperature of ta -20 … +50 °C
Ambient temperature of ta (at lifetime 50,000 h) 40 °C
Storage temperature of ts -40 … +80 °C
Lifetime up to 50,000 h
Dimensions L x W x H 97 x 43 x 22.5 mm
28002482 Wiring
Wiring type and cross section
The wiring can be in stranded wires with ferrules or solid with a cross section of 0.5–1.5 mm². Strip 8.5–9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals.
Use one wire for each terminal connector only.
Release of the wiring
Press down the “push button” and remove the cable from front.
28002482 Wiring guidelines
• All connections must be kept as short as possible to ensure good EMI behaviour.
• Mains leads should be kept apart from LED Driver and other leads (ideally 5 – 10 cm distance)
• Max. length of output wires is 2 m.
• The secondary wires (LED module) should be routed in parallel to ensure good EMC performance.
• Secondary switching is not permitted.
• Incorrect wiring can demage LED modules.
• To avoid the damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).
Replace LED module
1. Mains off
2. Remove LED module
3. Wait for 10 seconds
4. Connect LED module again
28002482 Installation instructions
The LED module and all contact points within the wiring must be sufficiently insulated against 1 kV surge voltage.
Air and creepage distance must be maintained.
Insulation and electric strength testing of luminaires
Electronic devices can be damaged by high voltage.
This has to be considered during the routine testing of the luminaires in production.
According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each luminaire should be submitted to an insulation test with 500 V DC for
1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal.
The insulation resistance must be at least 2 MΩ.
As an alternative, IEC 60598-1 Annex Q describes a test of the electrical strength with 1500 V AC (or 1.414 x 1500 V DC). To avoid damage to the electronic devices this test must not be conducted.
Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.
Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.
In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.
Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.
Need to know more about Tridonic 28002482 LC 20W 500mA fixC SC ADV – Huge UK Based Stock?
You can email us at: sales@ledparts.co.uk or alternatively you can request a callback by completing the form below and we'll get back to you as soon as possible.












