Tridonic 89899859 EM powerLED 2 W BASIC SCREW-FIX – Huge UK based stock

89899859 Common Data

Rated supply voltage 220 – 240 V
Mains frequency 50 / 60 Hz
Forward voltage range LED module (1 x LED) 1 2.8 – 3.4 V

Forward voltage range LED module (2 x LED) 1 5.6 – 6.8 V
Max. open circuit voltage 10 V
Mains current, 1 W device 30 mA
Mains current, 2 W device 40 mA

Power in mains operation, 1 W device 3.5 W
Power in mains operation, 2 W device 5 W
Starting time 0.31 s from detection of emergency event

Overvoltage protection 320 V (for 1 h)
Battery discharge current Refer to data sheet
Max. casing temperature tc 70 °C
Ambient temperature ta -25 … +50 °C

Mains voltage changeover threshold According to EN 60598-2-22
Type of protection IP20
Lifetime up to 50,000 h

The 89899859 can be provided as a kit with the appropriate NiMH battery if required, see our YUASAS 5SCM3-0L4 6.0V 3AH NiMH Stick battery and 5/1SCM3-A 6.0V 3AH NiMH Side-by-side battery for suitability.

89899859 Wiring

89899859 Wiring instructions

• The EM powerLED terminals, battery, indicator LED and test switch terminals are classified as SELV. Keep the wiring of the DALI and the input terminals separated from the wiring of the SELV terminals or consider special wiring (double insulation, 6 mm creepage and clearance) when these connections should be kept SELV.

• The output to the LED is DC but has high frequency content at 125 kHz, which should be considered for good EMC compliance.
• EM powerLED leads should be separated from the mains and DALI connections and wiring for good EMC performance.
• Maximum lead length on the EM powerLED terminals is 3 m. For a good EMC performance keep the LED wiring as short as possible.

• The secondary wires (LED module) should be routed in parallel to ensure good EMC performance.
• Maximum lead length for the test switch and Indicator LED connection is 1 m. The test switch and Indicator LED wiring should be separated from the EM powerLED leads to prevent noise coupling.

• Battery leads are specified with 0.5 mm2 cross section and a length of < 1.3 m.
• Switched live and unswitched live supplies must be off the same phase.
• To avoid the damage of the control gear, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).

89899859 Jumper selection

Module supplied with jumper in 3 hours position (position B).

The position of the link will only be read on first power up. If it is changed afterwards both the battery and mains supply must be disconnected for 10 seconds to enable the EM powerLED to read the new link position on reconnection of the battery and mains. It will lead to a false battery failure indication if the link is changed after installation without this reset.

Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.

Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.

In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.

Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.