Mean Well XLG-75-H-A – 75W 650 – 2100mA Constant Current LED Driver, With IP67 Protection

XLG-75-H-A Technical Information

XLG-75-H-A Output

Rated Current 1400mA
Rated Power 75W
Constant Current Region 27 ~ 56V
Open Circuit Voltage (max.) 60V
Current ADJ. Range 650~2100mA
Current Ripple 3.0%(@rated current)
Current Tolerance ±5%
Set up Time 500ms/230VAC, 1200ms/115VAC

XLG-75-H-A Input

Voltage Range 100 ~ 305VAC, 142VDC ~ 431VDC
Fequency Range 47 ~ 63Hz
Power Factor (Typ.) PF≧0.97 / 115VAC, PF≧0.95 / 230VAC, PF≧0.92 / 277VAC at full load
Total Harmonic Distortion THD< 10% (@ load≧50% at 115VAC/230VAC ,@load≧75% at 277VAC)
Efficiency (Typ.) 90%
AC Current (Typ.) 1A / 115VAC 0.45A / 230VAC 0.38A / 277VAC
Inrush Current (Typ.) COLD START 50A(twidth=300μs measured at 50% Ipeak) at 230VAC; Per NEMA 410
Max. NO. of PSUs on 16A CIRCUIT BREAKER 9 unit(circuit breaker of type B) / 14 units(circuit breaker of type C) at 230VAC
Leakage Current<0.75mA / 277VAC
Standby Power Consumption Standby power consumption <0.5W for AB-Type(Dimming OFF)(for standard version)

XLG-75-H-A Protection

Over Power 110 ~ 150% Hiccup mode, recovers automatically after fault condition is removed
Short Circuit Hiccup mode or Constant current limiting, recovers automatically after fault condition is removed
Input Over Voltage 320 ~ 370VAC (Shut down output voltage when the input voltage exceeds protection voltage, recovers automatically after fault condition is removed) Can survive input voltage stress of 440Vac for 48 hours(Input over voltage only for XLG-75I series)
Over Temperature Shut down output voltage, re-power on to recovery

XLG-75-H-A Environment

Working Temp. Tcase=-40 ~ +90℃(Please refer to “OUTPUT LOAD vs TEMPERATURE” section)
Max. Case Temp. Tcase=+90℃
Working Humidity 20 ~ 95% RH non-condensing
Storage Temp., Humidity -40 ~ +80℃, 10 ~ 95% RH non-condensing
Temp. Coefficient ±0.03%/℃ (0 ~ 60℃)
Vibration 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes

XLG-75-H-A Safety & EMC

Safety Standards UL8750(type”HL”), CSA C22.2 No. 250.13-12; ENEC BS EN/EN61347-1, BS EN/EN61347-2-13 independent, BS EN/EN62384;EN 60335-1
compliant to EN 60335-2-89 Annex BB, EN 60335-2-24 Annex CC;GB/T19510.1,GB/T19510.213; EAC TP TC 004;J61347-1(H29), J61347-2-13
(H29),KC61347-1,KC61347-2-13,IS15885(Part2/Sec13)(for XLG-75I type only); NOM-058-SCFI-2017(except for Blank type);IP67 approved
Withstand Voltage I/P-O/P:3.75KVAC I/P-FG:2KVAC O/P-FG:1.5KVAC
Isolation Resistance I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH

Others

Part Number XLG-75-H-A
MTBF 3404.7K hrs min. Telcordia SR-332 (Bellcore) ; 276.3Khrs min. MIL-HDBK-217F (25℃)
Dimension 140*63*32mm (L*W*H)
Packing 0.58Kg;24pcs /15Kg /0.85CUFT

Also stocked within the XLG-75 series

XLG-75-24-A

Constant current (CC) LED drivers are specialized power supplies that deliver a fixed, stable current (e.g., 350mA, 700mA) while varying the output voltage to match the LED load’s requirements. Essential for high-power LEDs and series-wired circuits, they prevent thermal runaway, ensure consistent brightness, and extend LED lifespan.

Key Aspects of Constant Current LED Drivers:

Functionality: Unlike constant voltage drivers, CC drivers automatically adjust their voltage output within a specified range to keep the amperage constant.

Applications: Ideal for high-power LEDs, downlights, spotlights, and COB modules. They are crucial when LEDs are wired in series.

Benefits: Prevents, excessive current, which leads to premature burnout or “thermal runaway,” where heat causes the LED to draw more power, leading to failure.

Specifications: Usually rated by amperage (mA or A) and a voltage range (e.g., 700mA, 13~26V).

Dimming & Control: Many models support dimming methods like DALI, 1-10V, or TRIAC

Constant voltage (CV) LED drivers convert AC mains power to a stable, low-voltage DC (typically 12V or 24V) required for LED strip lights and modules. They are designed for parallel circuits where voltage must remain consistent to prevent flickering and ensure proper, long-lasting performance.

Key Aspects of Constant Voltage LED Drivers:

Applications: Primarily used for LED tape/strips, under-cabinet lighting, signage, and architectural lighting.

Voltage Output: Usually 12V DC or 24V DC.

Selection Criteria:

Voltage: Match the driver voltage to the LED strip voltage (e.g., 12V LED needs a 12V driver).

Wattage: Select a driver with a total wattage capacity higher (typically 20% over) than the total load of the LED strip.

Advantages: More cost-effective than constant current drivers, allowing for easy installation of multiple lights in parallel.

Dimming Options: Compatible with various dimming methods, including DALI, 0-10V, and TRIAC

Established in 1982, headquartered in New Taipei City, MEAN WELL is a Standard Power Supply manufacturer and dedicated to developing specialized industrial power supplies solutions for decades.

Marketed worldwide with its own brand “MEAN WELL”, MEAN WELL power supply has been widely used in all industries and almost everywhere in your life. From home espresso machine, Gogoro electric scooter charging station, to the well-known landmark Taipei 101 skyscraper top lighting and Taoyuan International Airport jet bridge lighting, all of these you will surprisingly find MEWN WELL Power hidden inside, functioning as the heart of the machine, providing stable voltage and current for a long time, and powering up the whole machine and system to operate smoothly.

MEAN WELL Power has been widely used in different industries such as Industrial Automation, LED Lighting/ outdoor signage, Medical, Telecommuting, Transportation and Green Energy applications.

MEAN WELL has maintained a long term, solid relationship with our customers, suppliers, and employees in the spirit of “good intention” and “reliable partner” commitments since the company founded. Over the years, MEAN WELL has built hundreds of reliable partnership around the world.