Tridonic 28002489 LC 60W 1050mA fixC SC ADV – Limited Stock

28002489 Common Data

Ordering data LC 60W 1050mA fixC SC ADV 28002489

28002489 Technical Data

Rated supply voltage 220 – 240 V
AC voltage range 198 – 264 V
Mains frequency 50 / 60 Hz
Overvoltage protection 320 V AC, 1 h
THD (at 230 V, 50 Hz, full load) < 10 %
Output current tolerance 1 ± 7.5 %
Typ. current ripple (at 230 V, 50 Hz, full load) ± 5 %
Output P_ST_LM (at full load) ≤ 1
Output SVM (at full load) ≤ 0.4
Max. output voltage (U-OUT) 70 V
Starting time (at 230 V, 50 Hz, full load) ≤ 0.5 s

Turn off time (at 230 V, 50 Hz, full load) ≤ 0.2 s
Hold on time at power failure (output) 0 s
Ambient temperature ta -20 … +50 °C
Ambient temperature ta (at lifetime 50,000 h) 40 °C
Storage temperature ts -40 … +80 °C
Lifetime up to 50,000 h
Guarantee (conditions at www.tridonic.com) 5 Year(s)
Dimensions L x W x H 150 x 43 x 30 mm
Dimensions with strain-relief L x W x H 210 x 43 x 30 mm

28002489 Standards

EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1
EN 61347-2-13
EN 61547
EN 62384

Glow-wire test

according to EN 61347-1 with increased temperature of 850 °C passed.

Thermal details and lifetime

The 28002489 are designed for a lifetime stated above under reference conditions and with a failure probability of less than 10 %.

The relation of tc to ta temperature depends also on the luminaire design. If the measured tc temperature is approx. 5 K below tc max., ta temperature should be checked and eventually critical components (e.g. ELCAP) measured. Detailed information on request.

28002489 Wiring type and cross section

For wiring use stranded wire with ferrules or solid wire from 0.5–1.5 mm².
Strip 8.5–9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals.
Use one wire for each terminal connector only.

Release of the wiring

Press down the “push button” and remove the cable from front.

Fixing conditions when using as independent Driver with Clip-On

Dry, acidfree, oilfree, fatfree. It is not allowed to exceed the maximum ambient temperature (ta) stated on the device. Minimum distances stated below are recommendations and depend on the actual luminaire. Is not suitable for fixing in corner.

Device not suitable for covering with thermally insulating material according to IEC 60598-1 Ed.9

28002489 Wiring guidelines

• All connections must be kept as short as possible to ensure good EMI behaviour.
• Mains leads should be kept apart from LED driver and other leads (ideally 5 – 10 cm distance)
• Max. length of output wires is 2 m.
• To comply with the EMC regulations run the secondary wires (LED module) in parallel.
• Secondary switching is not permitted.
• Incorrect wiring can damage LED modules.
• To avoid damage of the Driver, the wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).

Replace LED module

1. Mains off
2. Remove LED module
3. Wait for 10 seconds
4. Connect LED module again
Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs.

Installation instructions

The LED module and all contact points within the wiring must be sufficiently insulated against 1 kV surge voltage.
Air and creepage distance must be maintained.

Mounting of device

Max. torque for fixing: 0.5 Nm/M4

Functions

Short-circuit behaviour

In case of a short circuit on the secondary side (LED) the 28002489 switches off. After elimination of the short-circuit fault the LED driver will recover automatically.

No-load operation

The 28002489 will work in a pulsed light output mode to limit the output voltage lower than 60 V which allows the application to be able to work safely when LED string opens due to a failure.

Overload protection

If the maximum load is exceeded by a defined internal limit, the LED driver reduces the LED output current. If the output voltage is exceeded by a certain degree the driver will start working in a pulsed light output mode. After elimination of the overload the nominal operation is restored automatically.

Overtemperature protection

The LED driver will reduce the LED output current or it works in a pulsed light output mode if the temperature reaches a certain degree.

Output over voltage protection

The LED driver will work in a pulsed light output mode to limit the output voltage lower than 60 V, even in fault conditions.

Miscellaneous

Insulation and electric strength testing of luminaires

Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production.

According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each luminaire should be submitted to an insulation test with 500V DC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal. The insulation resistance must be at least 2MΩ.

As an alternative, IEC 60598-1 Annex Q describes a test of the electrical strength with 1500V AC (or 1.414 x 1500V DC). To avoid damage to the electronic devices this test must not be conducted.

Conditions of use and storage

Humidity: 5 % up to max. 85 %, not condensed (max. 56 days/year at 85 %)
Storage temperature: -40 °C up to max. +80 °C

The devices have to be within the specified temperature range (ta) before they can be operated.

The LED driver is declared as inbuilt LED controlgear, meaning it is intended to be used within a luminaire enclosure.

If the product is used outside a luminaire, the installation must provide suitable protection for people and environment (e.g. in illuminated ceilings).

Maximum number of switching cycles

All LED driver are tested with 50,000 switching cycles.

Compact, non-dimmable constant current LED drivers are compact power supplies designed to deliver a fixed, steady current (mA) to LEDs, ensuring consistent brightness and longevity. They are ideal for space-constrained, fixed-intensity applications like downlights, under-cabinet lighting, and spot lighting. These drivers prevent flickering and overheating, often featuring lightweight, plastic cases.

Key Aspects of Compact Non-Dimmable Constant Current Drivers

Performance: They deliver a fixed current (e.g., 350mA, 700mA) regardless of voltage fluctuations, ensuring consistent brightness.

Applications: Ideal for, but not limited to, LED downlights, spot lights, and signage where dimming is not required.

Design & Size: Specifically engineered to be small, making them suitable for installations with limited space, such as recessed fixtures.

Safety Features: Often equipped with protections against short circuits, overloads, and high temperatures.

Input/Output: Typically convert high-voltage AC mains to low-voltage DC, suited for series-connected LEDs.

Common Ratings: Available in various power levels, such as 15W compact models for small-scale projects.

Why Choose Non-Dimmable?

Reliability: Without dimming components, these drivers are highly reliable for applications requiring continuous, full-power illumination.

Cost-Effective: Often more economical than dimmable alternatives.

Simplicity: Simple installation for, e.g., task lighting where brightness levels are fixed.

Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.

Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.

In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.

Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.