Tridonic 87500269 LCI 100W 2100mA TEC C – Limited Stock

87500269 Technical data

Rated supply voltage 220 – 240 V
AC voltage range 198 – 264 V
Rated current (at 230 V, 50 Hz) 0.47 A
Mains frequency 50 / 60 Hz
Overvoltage protection 300 V AC, 1 h
Max. input power 115 W
Output power range 50 – 100 W
THD (at 230 V, 50 Hz, full load) < 10 %
THD (at 230 V, 50 Hz, min. load) < 15 %

Output current tolerance 1 ± 7.5 %
Typ. current ripple (at 230 V, 50 Hz, full load) < 3 %
Output P_ST_LM (at full load) ≤ 1
Output SVM (at full load) ≤ 0.4
Starting time (at 230 V, 50 Hz, full load) ≤ 0.5 s
Turn off time (at 230 V, 50 Hz, full load) ≤ 0.5 s
Hold on time at power failure (output) 0 s
Ambient temperature ta -25 … +60 °C
Ambient temperature ta (at lifetime 50,000 h) 60 °C
Storage temperature ts -40 … +80 °C
Type of protection IP20
Dimensions L x W x H 140 x 100 x 30 mm

87500269 Standards

EN 55015
EN 61000-3-2
EN 61000-3-3
EN 61347-1
EN 61347-2-13
EN 61547
EN 62384

87500269 Overload protection

If the maximum load is exceeded by a defined internal limit, the LED driver reduces the LED output current. After elimination of the overload the nominal operation is restored automatically.

87500269 Overtemperature protection

The LED driver is protected against temporary thermal overheating. If the temperature limit is exceeded, the unit shuts down itself and then turns
on when it cools down. After the elimination of over temperature fault, the nominal operation is restored automatically. The temperature protection is activated typically at 7 °C above tc max.

Short-circuit behaviour

In case of a short circuit on the secondary side (LED) the LED driver will latch-up. The LED driver will recover itself when the short-circuit fault is removed and the AC is recycled (turn off the AC for longer than 0.5 s and then turn on).

No-load operation

The LED driver works in constant voltage mode. In no-load operation the output voltage will not exceed the specified max. output voltage (no-load voltage, refer to page 1).

Conditions of use and storage

Humidity: 5 % up to max. 95 %, not condensed (max. 56 days/year at 95 %)

Storage temperature: -40 °C up to max. +80 °C

The devices have to be within the specified temperature range (ta) before they can be operated.

Glow-wire test

according to EN 61347-1 with increased temperature of 850 °C passed.

Installation instructions

The LED module and all contact points within the wiring must be sufficiently insulated against 500 V surge voltage.
Creepage distances and clearances must be maintained.

Replace LED module

1. Mains off
2. Remove LED module
3. Wait for 10 seconds
4. Connect LED module again

Hot plug-in or secondary switching of LEDs is not permitted and may cause a very high current to the LEDs.

87500269 Wiring type and cross section

For wiring use stranded wire with ferrules or solid wire from 0.5 – 1.5 mm². Strip 8.5 – 9.5 mm of insulation from the cables to ensure perfect operation of the push-wire terminals (WAGO 250).

87500269 Wiring instructions

The secondary leads should be separated from the mains connections and wiring for good EMC performance. Maximum lead length on secondary side is 2 m. For a good EMC performance keep the the LED wiring as short as possible.

87500269 Wiring guidelines

• All connections must be kept as short as possible to ensure good EMI behaviour.
• Mains leads should be kept apart from LED driver and other leads (ideally 5 – 10 cm distance)
• Max. length of output and I sel wires is 2 m.
• Secondary switching is not permitted.
• Incorrect wiring can demage LED modules.
• The wiring must be protected against short circuits to earth (sharp edged metal parts, metal cable clips, louver, etc.).

Insulation and electric strength testing of luminaires

Electronic devices can be damaged by high voltage. This has to be considered during the routine testing of the luminaires in production.

According to IEC 60598-1 Annex Q (informative only!) or ENEC 303-Annex A, each luminaire should be submitted to an insulation test with 500V DC for 1 second. This test voltage should be connected between the interconnected phase and neutral terminals and the earth terminal.

The insulation resistance must be at least 2MΩ. As an alternative, IEC 60598-1 Annex Q describes a test of the electrical strength with 1500V AC (or 1.414 x 1500V DC). To avoid damage to the electronic devices this test must not be conducted.

Conditions of use

The LED driver is declared as inbuilt LED controlgear, meaning it is intended to be used within a luminaire enclosure.

If the product is used outside a luminaire, the installation must provide suitable protection for people and environment (e.g. in illuminated ceilings).

Maximum number of switching cycles

All LED driver are tested with 50,000 switching cycles.

LED Drivers: Constant Current vs. Constant Voltage …Constant current (CC) LED drivers provide a fixed output current, usually measured in milliamps (mA), while automatically adjusting output voltage to ensure consistent brightness and protect LEDs from overdriving and thermal runaway. They are essential for high-power LED applications, single-bulb, or series-connected LED setups.

Key Features and Benefits

Constant Current Regulation: Maintains a steady flow of electricity, preventing voltage fluctuations that cause flickering.

Extended Lifespan: Protects against overcurrent and heat-related failure.

Optimal Performance: Ensures consistent color and brightness across lighting systems.

Versatile Dimming: Many models support dimming protocols such as 0-10V, DALI, and PWM.

Applications

Series-Connected Lighting: Ideal for LED spotlights, downlights, and MR16/GU10 bulbs.

High-Power LEDs: Used where precise current control is necessary, such as in retail, museum, and commercial office lighting.

Selection Factors

Current Requirement (mA): The driver must match the specific mA rating of your LED load (e.g., 350mA, 700mA, 1050mA).

Voltage Range: Must handle the total voltage range required by the series of LEDs.

Power Output: Total power (Watts) should exceed the total load

Tridonic are a Zumtobel Group company, founded in 1956 in Dornbirn, Austria. For more than 60 years, they have been a driving force in the development of professional lighting solutions.

Today, Tridonic is a world-leading provider of lighting technology for professional applications, including office buildings, and retail outlets, hotels and restaurants, the education industry and outdoor lighting sectors.

In Tridonics’ extensive range of energy-efficient dimmable and non-dimmable LED drivers they offer the right products for every indoor and outdoor application – from cost-efficient LED drivers in proven Tridonic quality to premium products that give you maximum flexibility and convenience.

Tridonics’ dimmable LED drivers can be controlled with different analog and digital dimming signals. Tridonic basicDIM Wireless products allow wireless control without additional wiring.